How to make a Crossbody Bag with Bottle Holder
Conveniently carry a water bottle or tumbler!! I made a sling crossbody bag with a bottle holder.
It's a small bag that's just the right size to hold a cell phone or wallet, so it's great for going out lightly.
My detailed and friendly tutorial will help you make your own bottle sling bag.
The finished measurements of this pouch are approximately
12.5㎝(5″) W × 20㎝(8″) H × 10㎝(4″) D.
You may watch the full video tutorial on my Youtube channel.
Share this video with a lot of people who need it.
Let's get started!!
◎ Main Panel
② 14.5㎝ × 22㎝ (5¾″ × 8¾″) Outer layer
② 14.5㎝ × 22㎝ (5¾″ × 8¾″) Lining
◎ Bottle Holder
① 22㎝ × 36㎝ (8¾″ × 14⅛″) Outer layer
② 14.5㎝ × 9㎝ (5¾″ × 3⅝″) Outer layer
① 22㎝ × 36㎝ (8¾″ × 14⅛″) Mid-weight woven fusible interfacing
① 14.5㎝ × 9㎝ (5¾″ × 3⅝″) Mid-weight woven fusible interfacing
◎ Zipper Panel
② 27㎝ × 3㎝ (10¾″ × 1¼″) Outer layer
② 27㎝ × 3㎝ (10¾″ × 1¼″) Lining
◎ Side Panel
① 40㎝ × 5㎝ (15⅞″ × 2″) Outer layer
① 40㎝ × 5㎝ (15⅞″ × 2″) Lining
◎ Inside Pocket
① 14.5㎝ × 27㎝ (5¾″ × 10¾″) Lining
① 12.5㎝ × 12.5㎝ (5″ × 5″) Mid-weight woven fusible interfacing
◎ Others
① 25㎝ (9⅞″) Zipper
① 4㎝(1⅝″) wide bias tape 150㎝(59¼″)
① 2㎝(3/4″) wide Webbing Strap 100㎝(39½″)
The pattern for making this can be drawn by yourself by watching my YouTube video.
Fold the inner pocket wrong sides together in half, and sew the top.
Place the inner pocket on the right side of the lining and sew.
With assembled lining right side up, center zipper right side facing up along top edge. Place the outer layer, right side down on top. Pin in place. Using your zipper foot, sew along top edge using a 1cm seam allowance.
Attach the outer and lining to the other side of the zip the same way.
Open out, press pieces away from and top stitch on both 0.2cm away from the zipper.
Fold the bottle holder fabric wrong sides together in half, and sew the top.
Place it on the bottom of the bottle holder and sew with a 0.7cm seam allowance.
Place the right side of the other bottom fabric on top of it. Sew with a 1cm seam allowance.
And turn right side out.
Place the bottle holder on the right side of the outer layer and sew.
Place the side panel around the outer layer. Sew with an allowance of about 3/8″.
The bias tape is placed and pinned as pictured, stitch up to the end.
Stitch from the right side seam into seam, or sew manually from the backside.
You are finished!!!
(●'◡'●)
You might like these bags and pouches
