DIY Fabric Wallet with Necklace String and Card Holders
Join us in this fun sewing tutorial to craft your own Necklace Card Wallet.
This wallet is small and made from fabric, featuring a front pocket for coins and four card holders inside.
The necklace string attached to a hook makes it easy to wear around your neck.
Ideal for all levels of sewing enthusiasts, this project is both enjoyable and useful.
The finished measurements of this wallet are approximately
9㎝(3⅝″) W × 11㎝(4⅜″) H
You may watch the full video tutorial on my Youtube channel.
Share this video with a lot of people who need it.
Let's get started!!
◆ Main Panel
① 11㎝ × 4.5㎝ (4⅜″ × 1¾″) Outer layer
① 11㎝ × 22.5㎝ (4⅜″ × 8⅞″) Outer layer
① 11㎝ × 25㎝ (4⅜″ × 9⅞″) Lining
① 9㎝ × 23㎝ (3⅝″ × 9⅛″) Mid-weight woven fusible interfacing
◆ Flap
① 8㎝ × 11.5㎝ (3¼″ × 4½″) Outer layer
① 8㎝ × 11.5㎝ (3¼″ × 4½″) Lining
① 8㎝ × 11.5㎝ (3¼″ × 4½″) Mid-weight woven fusible interfacing
◆ Front Pocket
① 13㎝ × 11㎝ (5⅛″ × 4⅜″) Outer layer
① 13㎝ × 11㎝ (5⅛″ × 4⅜″) Lining
① 11㎝ × 9㎝ (4⅜″ × 3⅝″) Mid-weight woven fusible interfacing
◆ Card Holder
① 10㎝ × 26㎝ (4″ × 10¼″) Lining
① 10㎝ × 32㎝ (4″ × 12⅝″) Lining
◆ Side Panel
② 8.5㎝ × 18㎝ (3⅜″ × 7⅛″) Lining
◆ Others
① 1㎝ (3/8″) Wide Swivel Snap
① 4㎝ (1⅝″) Wide bias tape 30㎝(11⅞″)
① 1㎝ (3/8″) Wide Webbing Strap 95㎝(37⅜″)
① Snap Buttons
Cut the fabric into the shape of the pattern.
Place the wrong sides together of the flap fabrics and sew all the edges.
Place the right sides together of the outer and bias tape and sew with an allowance of about 1㎝(3/8″).
Fold the bias twice and sew.
Place the flap between the outer layers of the main panel and sew.
Place the right sides together of the front pocket fabrics and sew the top and bottom seam.
Turn the pocket right side out.
Place the front pocket on the right side of the main panel.
Sew 3 sides, leaving the top.
Fold the short card pocket fabric in half and sew.
Turn it right side out.
Place it in the center of the long card pocket fabric.
Fold the long card pocket fabric in half and sew, leaving an opening.
Turn them right side out.
Place the card holder on top of the lining and sew both sides.
Place the right sides together of the outer and lining and sew with an allowance of about 1㎝(3/8″), leaving an opening.
Turn it right side out by pulling the fabric through the opening.
Press around all the edges.
Fold the side panel right sides together in half.
Sew 3 sides, leaving an opening.
Turn it right side out.
Fold it vertically and stitch along edges of the side, 0.3cm(1/8'') from the edge.
Place the side panel 2.5cm(1″) below the top of the main panel and sew.
Fold the main panel in half, align the other side of the side panel, and sew.
Attach the strap.
RELATED STORIES :
